Kingston (SSS6690\SK6211) u disk volume production full tutorial (already supports 8G) fix the article.
April 5, 2010 4:34 pm Monday. .
Kingston (SSS6690\SK6211) u disk volume production full tutorial (already supports 8G) fix the article.
Repair articles:. .
So if production errors or failed? I to talk about specific methods!.
First use ChipGeniusV3. .1 Tool to scan, and sometimes use the non-production software file results surprise you, as follows:. .
No error occurs, no mass production will not be damaged u disk. Unless your USB disk, bad road, so low that in advance the best look for your USB drive).
Guarantee that no bad sectors U-disk is preparing well SK6211_20080125_BA (to facilitate the call can own it up good to remember the name), then also, and mass production through the same interface (say you are ignored here). .
Didn't see this error (it is in the picture, you can ignore).
This time to ignore it, because your U disk has a problem of mass production. Continue to repair! . .
Keep the default above stuff, don't worry!, and so on down into, to continue.
Select this button for volume production (No matter what tips do not care, as long as continue on it). .
And then he will receive the following error message.
Failed Oh, this is normal is to like this, and this shows a response U disk (in the process forget about the U drive in the computer any tips). .
And then select Reset button, as follows:.
Wait for it to reset to complete and you are prompted "ERRO OK" the dialog, then "off" switch off SK6211_20080125_BA (a bit wordy Ha ha). .
The module has been detected, but the volume is still not recognized, Oh already fix it patience!.
SK6211_20080125_BA then turn it on again. This time it prompted a discovery device, but can be identified into a U-disk. .
This is detected by the device status, huh, huh doesn't seem to ignore its capacity. Now you can turn off SK6211_20080125_BA tool, Oh.
Note: Do not pull out after the completion of repair U disk, and do not directly use the repair tool production (because of version compatibility problems) or else will go wrong, you took the trouble I Xianlei it! ! Ha ha. .
It then uses the ChipGeniusV3. .1 scan once to see results.
The make and model also shows, how to become a SK6281? Model has become SK6201? Do not rush, which is compatible identification, indicating that the main chip repair is successful, although some of the above methods appears very wordy, but the insurance. .
Step I do not say.
However, the parameters here, if so (you can enter the parameters set in to change):. .
This is recovery KingstonU.
According to the method before the final production once again, as long as a close look at the first mass production can be successful tutorial. .
Mass production after the success of the "off" point off SK6211_20090227_BA (this step is very important), unplug the USB drive plugged in again. Then use the .1 ChipGeniusV3. scanned once.
Get results:. .
Is not lost and bring you the chip model (just the original SSS6690 SSS6677 is changed)!! hehe after completion of the course the mass production of IC master displayed will vary (possibly ChipGenius software recognition problem) but it does not affect the use, after all, this is an emergency mass production repair, you can ignore it.
Repair notes, repair property after the U disk is 0 bytes, can not be used and formatted. It does not matter, let U disk to maintain the machine, do not unplug the U disk (remember), to correct production on the line. This method is suitable for SK6211 Series U disk. Because this area is also trying to work so if imperfect production actively put forward, please. .
The above said USBCDROM production method, of course, this way you can also have a regeneration USBHDD boot disk can be made.
If you feel satisfied, would like one more USBZIP the boot disk how to do? Now I come back briefly. .
The figure above is through these settings for many graphic boot USB disk. If not set to "read-only", not when you can do store!.
FLASH read 45 error is failure of production of this situation and choose the wrong type the FLASH. To address this situation in three ways:. .
A replacement for other versions continue to volume production.
Two split shell directly see the specific models FLASH chip FLASH and then select the correct model for mass production. .
Three of these two methods are disabled, shorted FLASH chip, 29, 30 pins, commonly to FLASH chip on one of the first pin counter-clockwise down (ignoring the FLASH model text direction), common FLASH 29, 30 pins is located in the u disk socket in the direction of sections 5, 6 feet. There are a few FLASH in diagonal with two circle, then to the big ring counterclockwise for first pins down FLASH model, regardless of the orientation of the text (for example, some Toshiba chips are two diagonal circle). The short answer is to plug in the USB disk on your computer and open the volume production tool, it is best to not use extension cords. . Also, if the process occurs in a short access time to time so identified disk instability can try another computer. .
Short answer, I found that if it is a double-mount type master plate may be shortened when no response, then you can weld under FLASH (to a certain welding technique) will it be in the right direction of the PIN soldered to the other side of the master, and then plug in the USB disk volume production, shorted. If the stick can occur after you acknowledge the capacity of the disc but the display and the difference between the original capacity and the capacity of the volume of post-partum are changing and unstable situations, you can stick the FLASH back to their original locations and then shorted to correctly identify the chip size.
User Comments:. .
1.
2. .
A landlord said that access errors, follow the landlord method operation, or no difference or that cannot be released to manufacturing. What's up?.
3. .
?2010 Baidu。.
Source citation Kingston (SSS6690 \ SK6211) U disk volume full tutorial (already supports 8G) _ my space repair articles you happy with my life _ Baidu wonderful you unlimited space go hand in hand. .
